Watts K-1 Polyethylene Icemaker Kit, 25-Feet

• Complete kit with tubing and saddle valve
• Durable and long lasting
• Polyethylene tubing
• Easy to install for contractors or homeowners

I got this kit to run a water line from my kitchen sink to my refrigerator's ice maker. I am not a plumber, but I do understand the basic concepts of plumbing and have tackled a few small plumbing jobs. The included instructions are not the best if you need to be walked through every little step, but if you have an experience level similar to me you should be able to get through it.

The kit I got had slightly different pieces than what is in the product picture, however it did have everything I needed. The picture shows 2 nuts and some washers to go on the bolts that hold the two pieces of the saddle together. In the kit I received there were no nuts or washers because the nuts are actually welded to the bottom part of the saddle and the bolts just screw directly into them. All other pieces were the same.

According to the instructions the self-tapping saddle valve that comes with this kit can only be used to tap into a supply line that is 3/8" to 1-3/8" plastic or copper so make sure and check the size and material of the line you will tap into if you plan on using this valve. My sink line is mostly the flexible stainless steel, but fortunately there was about a foot of copper pipe between that and the faucet which I was able to tap into. The one problem I had with this kit was with threading the saddle onto the tap-valve. If you look at the product picture it shows the T-valve already has half of the "saddle" on it, but mine came with that saddle part separate. You are suppose to be able to just screw that saddle on the tap-valve (it's already threaded so should not be an issue), however the hole in the saddle was slightly too small. I had to take a pair of vice-grips and and adjustable wrench and man-handle the thing on. After a good bit of elbow grease I was able to finally get it on, though, and after that installing the valve was very easy. After you tighten the saddle around the pipe (and put the included rubber gasket below the T-valve), you simply start turning the T-valve clockwise as far as it will go and there is a spike inside that pierces the supply line. It was so easy that I did not even feel it going into the pipe and actually thought at first it wasn't going down far enough to pierce it. When I turned the valve back the other way, though, water started flowing just like it should.

Then it was just a matter of running the plastic line to my fridge and using the included supplies to connect it. I used plumbers tape on all the threads just as a precaution, but supposedly you do not have to if you don't want to.

I would again caution anyone who wants a clear step-by-step guide from this kit, but I think as long as you have a basic understanding of plumbing you will be OK. I am giving it 4 stars due to the saddle valve issue and since the instructions could be better. For the price, though, I think this is hard to beat.

Buy Watts K-1 Polyethylene Icemaker Kit, 25-Feet Now

The local HD was charging a lot more for this same kit so I came here. This installed without a problem, saddle valve seems like it'll hold up. A common problem I've seen with the valves is they start leaking after they've been used (open/closed) a lot so only time will tell if the 7$ was worth it. It's about the same quality you would find from any kit in the sub 20$ price range. I prefer polyethylene over copper because it's easier to work with needing to move fridge in and away from wall primarily. You also wont have the copper taste with poly likewise I noticed no real plastic or unusual tastes with this. If you wanted to do it right you could probably get a better PEX line, or even go with braided/SS. But, it probably won't pay off I expect this to last the life of the fridge.

Read Best Reviews of Watts K-1 Polyethylene Icemaker Kit, 25-Feet Here

No hesitations if you are needing to connect an ice maker and can use basic tools and read 9th grade English.

Want Watts K-1 Polyethylene Icemaker Kit, 25-Feet Discount?

I used this kit to install a water filter under the sink.While I didnt use all the items I used most of the kit.It is a good price for all that you get

Just as the other reviews say, the directions were not on point, then once we got it hooked up, the problem was the tubing could not take the water pressure running to the fridge even when it was turned down completely low.It kept popping off.Eventually we said for get it and ended up going to Bestbuy and buying the stainless steel product which worked absolutely great.Waste of money for us.The product seems to be made secure except for where the metal attachment and the cords meet.